When you have completed the preparation stage which includes measuring how much artificial grass you will need, installing appropriate drainage (if needed) and taking out the natural grass layer, you’ll be ready to install your artificial grass lawn. This post outlines the steps you ought to follow to help you to do the job right, from laying the base, connecting joints and preventing weed growth.
Lay Gravel Base then Sharp Sand – If required, use treated timber/timber stakes to put inside an area frame. We recommend 4 X 2 inches of tantalised treated timber for heavy clay soil areas and poorly draining areas and 2 X 2 inches of tantalised timber once and for all draining areas. Screw these timbers towards the stakes leaving the stakes on the inside the perimeter. Should the Artificial Grass meet a concrete path, wall or decking, position the timber flush using the surface height and also by using 10mm temporary fillet, pack the timber close to the wall leaving the room to help you tuck the fake grass santa clarita in between the timber as well as the adjoining material at a later stage.
Position the stakes up against the inner perimeter timber edging and hammer into the ground ensuring the stakes are slightly lower than the timber edging. Next screw the timber stake towards the timber edging. With heavy clay soils we recommend laying a crushed stone surface as high as 3 inches. This will not be necessary for the majority of areas and only required if you have a high water table where ground holds water for long periods of energy after it rains. Next compact the ground using a vibrating plate that can be hired from an equipment hire company. Guarantee the perimeter is compacted and underneath the timber edging by 1 inch. Infill the perimeter with sharp sand and level employing a rake. Ensure the sand is level to the peak in the timber edging and compact again.
Permanently drainage areas spread a layer of sharp sand to blind within the soil. Next compact the ground employing a vibrating plate which can be hired from an equipment hire company. Guarantee the perimeter is compacted and level using the timber edging. If you put more function in at this point, your Artificial Grass Lawn will appear better as a result.
Weed Control Layer – Apply the weed control geo textile membrane and cut as necessary. Tack using small 1 inch galvanised clout nails towards the timber edging. This weed control geo textile membrane prevents any chance of weed growth through the artificial grass drainage holes.
Roll out Artificial Grass – Lay the Artificial Grass inside the desired direction working on the carpet and not on the levelled base. Guarantee the carpet is positioned to minimise cuts, joints and waste overlaying the timber edging by at least 4 inches. If the artificial grass meets a path or edge, and in case you have laid the timber edging correctly as previously described, then your artificial grass can be wedged between. If joining, please ensure that the artificial grass is laid with all the pile running inside the same direction on every piece. Lay the carpet along with the sand as opposed to dragging it across the base material. To assist stop wrinkles or creasing it is best to allow 2 to three hours to settle before continuing with jointing and adhesive. Cut grass to shape utilizing a sharp Dolphin or Stanley knife or scissors.
Jointing – When jointing your outdoor carpet together, guarantee the pile runs within the same direction. Cut off manufacturer’s edge strip (if present) and butt two edges together ensuring there are no gaps more than 1mm between the two carpet edges. The accuracy of this will determine how visible the join is following the completion. Fold back edges and position jointing tape (smooth side down) so the edges from the carpet satisfy the tape when joined.
Adhesive – a) Apply the cartridge adhesive in a zig zag motion to the rougher side of the tape allowing one cartridge for every 3 linear metres. Reject carpet and press both edges into the wet adhesive, ensuring every piece marries up and contains no overlap. As you are carrying this out along with your fingers, mix the fibres together to conceal the join. Once the whole length is within place and also you are happy featuring its appearance it really is necessary to walk across the join repeatedly to activate the glue and bond the grass for the tape. Weigh along the seam to ensure good connection with the glue until it cures. The better care taken with the operation the neater and tidier the joint will likely be.
b) If making use of the 2-component multi-purpose adhesive, ensure thorough mixing of these two components before use. Apply adhesive to the rough side from the tape and spread evenly across a width of at least 20cm using when possible a notched trowel. Sufficient adhesive needs to be applied to ensure that when the artificial grass carpet is pressed to the adhesive, a transfer over the carpet backing is done. Reject carpet and press both edges into the wet adhesive, ensuring every piece marries up and contains no overlap. Ensure the carpet will not crest at the seam and is also holding flat within the bonded area. When the whole length is in place and also you are happy featuring its appearance it is essential to walk across the join several times to activate the glue and bond the grass towards the tape. Weight the seam to make sure good irfspy with the glue until it cures. The greater care taken with all the operation the neater and tidier the joint is going to be.
While you should endeavour to not put adhesive on the carpet small amounts of glue can be removed from the artificial grass fibre using White Spirit and a small off cut of the artificial grass. Small amounts of cured glue usually can be removed. To avert this situation and the possibility of damage to the artificial grass, care and precautions should be come to avoid contact with the fibres all the time. If the artificial grass has been jointed and glued and also you are pleased with the levels screw the grass to the timber perimeter framework using galvanised screws at the very least of 12 inch intervals.
Spread Sand (Optional, based on Grass Selected) – If the artificial grass has been laid use silica sand, which can be kiln dried and brush into carpet as you go. Each product could have sand infill but this is only used to stabilise the carpet and also at no time should the sand be visible. You have to obtain an even spread over the surface using a brush to develop the depth in layers. Do not apply the sand in one application. Brush sand into pile right after laying while the artificial grass is dry and while weather is good. Brush vigorously up against the fibres in the carpet pile to encourage the tufts to face upright. Putting the right quantity of sand in helps support the artificial grass to sleep down, protects the fibres as well as keeps them standing allow it the appearance of real grass.